<< Back to Laser Modules with Shutter Page

Laser Diode Modules with Shutter: 915nm

With Shutter for Safety, Built-In TEC Cooler and ACC Circuit Design

The DLXS-series 915 nm diode laser is constructed with features of integrated electronics, shutter for protection, built-in-TEC cooler, ACC (Automatic Current Control) circuit design, plug and play, good beam profile, miniaturization, international standard interface, and optional TTL or Analog modulation.  It is the ideal solution for a wide range of applications, including life sciences, environmental monitoring, inspection and machine vision.

***Note: The DLXS-series lasers are designated solely as OEM components for incorporation into the customer's end products. Therefore it is the customer's responsibility to comply with FDA requirements of FDA 21CFR, section 1040.10 and 1040.11 as complete laser product. 

SPECIFICATIONS

Model No.

DLXS-915-PFIDQ

Wavelength (nm)

9155

Output power (mW)

>50 (P=50), >100 (P=100)

Transverse mode

Near TEM00

Operating mode

CW

Power stability (rms, over 4 hours)

<1%

Noise of amplitude (rms, 20Hz-20MHz)

<1%
**<0.5% may be available upon request.

M2 factor

<1.5

Beam diameter at aperture (1/e2, mm)

~1.2

Beam divergence, full angle (mrad)

<1.0

Warm-up time (minutes)

<5

Beam height from base plate (mm)

19

Operating temperature (C)

10~35

Laser module

Dimensions

74.4(L) x40(W) x40(H) mm3

Weight

0.2 kg

Operating voltage

12VDC 4A

Modulation

None (Q=0)

TTL Modulation: 1Hz-1kHz (Q=T1), 1kHz-10kHz (Q=T2), 10kHz-30kHz (Q=T3), 30kHz-100kHz (Q=T4), 100kHz-300kHz (Q=T5), 300kHz-500kHz (Q=T6), 500kHz-1MHz (Q=T7)

Analog Modulation: 1Hz-1kHz (Q=A1), 1kHz-10kHz (Q=A2), 10kHz-30kHz (Q=A3), 30kHz-100kHz (Q=A4)

**Wider frequency ranges may be available upon request.

Expected lifetime (hours)

10,000

Warranty

10 months

Remarks

1.       The stability of output power may change when you adjust the output power.

2.       The laser head needs to be used on a heat sink with good heat dissipation.

3.       Optional AC adaptor with input voltage of 100-240VAC (Model No. AC12DC) is available upon request.

Dimension/Weight: 121(L) x50(W) x30.8(H) mm3, 0.3 kg

Dimensions of Laser Module and Power Supply (mm)

 Laser Module

Dimensions: 74.4(L) x40(W) x40(H) mm3
Weight: 0.2 kg

         

Optional AC Adaptor (Model No. AC12DC)

Dimension: 121(L) x50(W) x30.8(H) mm3
Weight: 0.3 kg

Note: The above specifications are subject to change without notice.

<< Back to Laser Modules with Shutter Page

PRODUCTS

VCSELs | Communication Lasers | Photodiode Receivers | Optical Transceivers | Fiber Optics | Optical Components 
 
Laser Diodes | Laser Modules | Laser Systems | Laser Accessories | Laser Products | Fiber Coupled LEDs

  For the code of Federal regulations, please refer to FDA PERFORMANCE STANDARDS FOR LIGHT-EMITTING PRODUCTS for detailed information.

  CONTACT US | HOW TO ORDER | QUO & INFO REQUEST | TERMS & CONDITIONS

Information contained herein is considered typical data. Lasermate Group, Inc. reserves the right to change or modify specifications of products at any time without notice.

Copyright by Lasermate Group, Inc.. All rights reserved.